Comtrol VS2000 V.34 Manuel d'utilisateur télécharger pdf

Product Overview

The InterChangeVS 2000 is an analog multimodem

virtual server that can be stacked or mounted in a rack.

This VS2000 contains eight 33.6K bps modem ports.

VS2000 features include:

• Eight RJ11 modem ports ready to connect to your

phone lines

• Diagnostic LEDs

VS-Link software provides the following features, which

are discussed in the VS2000 VS-Link Installation and

Configuration Guide:

• Backup server

• “Hot-swapping”

• Individual modem reset capability

• Terminal program (WCOM32)

• Port Monitor program (PORTMON)

See the VS2000 VS-Link

™ Installation and

Configuration Guide for information about installing

the software for this product and for reference

information for the AT command set.

Installing VS2000 Hardware

Use the following procedure to connect the VS2000.

1. Record the model and serial numbers of the VS2000.

2. Optionally, mount the VS2000 into the rack using

the enclosed mounting brackets. The unit is

designed to install in the rack with the front or back

of the unit facing the front of the rack.

Warning: If mounting the VS2000 into a rack mount

unit, make sure the rack is not top heavy.

3. Connect the cable from the appropriate Ethernet

connection (10Base-T or AUI) on the VS2000 to your

server or Ethernet hub.

Note: If connecting the VS2000 directly to the server, an

Ethernet crossover cable is required.

Note:

4. Connect the power cord.

5. Go to the Power-On Diagnostics discussion.

Power-On Diagnostics

When you switch a VS2000 on, it performs a self-

diagnostic. The results are displayed via the LED lights

on the back panel. If the unit is working correctly, the

following events should take place:

1. Turn the power switch to the On position.

2. All LEDs should light up briefly, to show that they

are working.

3. Both 10Base-T lights should remain lit after the

port LEDs go out, while the unit establishes the

Ethernet connection and polarity.

4. If using 10Base-T cabling, the lower LED remains

lit to indicate that the Ethernet connection is

established and polarity is correct.

5. The Port 2 LED begins flashing, to indicate that the

VS2000 is waiting for the server to initiate VS-Link

communications.

Note: The following steps only occur after you have

installed the VS-Link software. Use the VS2000

VS-Link Installation and Configuration Guide for

software installation information.

After installing the software, turn off the VS2000

and verify the full diagnostics sequence.

6. The upper 10Base-T LED flashes briefly, as the

server acquires control of the VS2000.

7. The port LEDs begin flashing in a “sweeping”

sequence, to indicate that the unit is operating

normally.

Note: See the following tables if you are not seeing the

LED sweeping sequence activity.

Serial Number* VS2000 Network Address*

00 C0 4E

* Identification tags are located on the back panel. You can

write this information on the blank sticker shipped with the

VS2000.

Server Running

VS-Link

Ethernet Connection

to Server or

Ethernet Hub

InterChangeVS™ 2000 V.34 North America

Hardware Installation Card

1 2 3 4

Résumé du contenu

Page 1 - Hardware Installation Card

Product OverviewThe InterChangeVS 2000 is an analog multimodem virtual server that can be stacked or mounted in a rack. This VS2000 contains eight 33.

Page 2 - Electromagnetic Compliance

Note: If using an AUI connection to the server, you can determine proper polarity by using an AUI to 10Base-T converter box.Modem CablesThe VS2000 mod

Page 3 - FCC Notices

Hardware SpecificationsThe following table illustrates hardware specifications:Safety NoticesInstallation of inside wire may bring you close to electr

Page 4 - Technical Support

6.No repairs are to be made by you. Repairs are to be made only by Comtrol or its licensees. Unauthorized repairs void the warranty and the registra

Commentaires sur ces manuels

Pas de commentaire

Comtrol VS2000 V.34 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Comtrol VS2000 V.34. Comtrol VS2000 V.34 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Comtrol VS2000 V.34