InterChangeVS™ 1000 SeriesVS1000 and VS1100HardwareInstallation and ConfigurationGuide
10 Installation OverviewIntroduction“Hot-Swapping” a VS1000Replacing a VS1000 with an identical VS1000A. Hardware Installation1. Power-down the VS1000
Obtaining Software or Document Updates 11IntroductionObtaining Software or Document UpdatesFor information that is not in this Guide, see the README a
12 Technical SupportIntroductionTechnical SupportComtrol has a staff of support technicians available to help you. U.S. telephone support is available
Hardware Installation Overview 13Installing the HardwareHardware Installation OverviewPerform the following steps to install your virtual server:• Ins
14 Installing the VS1000 HardwareInstalling the Hardwarea. Attach the L brackets to the VS1000 using the screws supplied with the unit.b. Attach the L
Installing VS1100 Hardware 15Installing the Hardware5. Make sure the power switch is set to Off (0).6. Connect the power cord to the unit and plug it
16 Installing VS1100 HardwareInstalling the HardwareOR• Attach the adhesive feet to the depressions in the bottom of the VS1100 and place the unit on
Power-On Diagnostics 17Installing the HardwarePower-On DiagnosticsWhen you switch a VS1000 base unit on, it performs a self-diagnostic. The results ar
18 Power-On DiagnosticsInstalling the HardwareNote: If using an AUI connection to the server, you can determine proper polarity by using an AUI to 10B
Connecting Devices 19Installing the HardwareConnecting DevicesUse the following procedure to connect RS-232 asynchronous devices to the VS1000/1100 po
Copyright © 1998. Comtrol Corporation. All Rights Reserved.Third Edition, April 8, 1998Comtrol Corporation makes no representations or warranties with
20 Replacing Units in Service (“Hot-Swapping”)Installing the HardwareReplacing Units in Service (“Hot-Swapping”)In the event that a VS1000 needs to be
Serial Cable Specifications 21Building CablesThis section contains information on how to build your own cables.Serial Cable SpecificationsIf building
22 Serial Cable SpecificationsBuilding CablesBuilding an RJ45 to DB25 CableUse the following figures if you need information about building a general-
Ethernet Cable Specifications 23Building CablesEthernet Cable SpecificationsFor Ethernet, use an unshielded twisted-pair (UTP) cable with a maximum le
24 Ethernet Cable SpecificationsBuilding CablesEthernet AUI Connector Pinout (VS1000 Only) This section shows an illustration of the female, high-dens
Remote Connector 25Building CablesRemote ConnectorThe DB9 port labeled “Remote” is reserved for Comtrol Corporation repair and maintenance use. No use
26 Building Loopback PlugsBuilding Cables
Hardware Conditions 27InterChangeVS SpecificationsHardware Conditions The following table lists the InterChangeVS unit conditions.Hardware Specificat
28 Electromagnetic ComplianceInterChangeVS SpecificationsElectromagnetic ComplianceThe following table illustrates electromagnetic Compliance for the
Power Supply Requirements 29InterChangeVS SpecificationsPower Supply RequirementsAll VS1000 units include an auto-switching power supply that automati
3Table of ContentsList of Tables...5Introduction...
30 Power Supply RequirementsInterChangeVS Specifications
Radio Frequency Interference (RFI) (FCC 15.105) 31NoticesRadio Frequency Interference (RFI) (FCC 15.105)The InterChangeVS1000 virtual server has been
32 Serial Cables (FCC 15.27)NoticesSerial Cables (FCC 15.27) This equipment is certified for Class A operation when used with unshielded cables.Underw
33Numerics10Base-Tcable connection14connector pinout23diagnostic LEDs17polarity17Aaddressdetermining the VS1000 network address13AUI14, 24Bbase unit (
34IndexIinstallingVS100013VS1000 rack13VS110015VS1100 rack15IntranetWare7LLEDs10Base-T17port18power up sequence17limitationsMultilink PPP7loopback plu
35Indexprerequisites7Ttechnical supportcontacting11information required13terminator plugVS100014VS110016troubleshootingdownloaded driver files11extrac
Part Number: 6610D April 8, 1998
4Table of ContentsEthernet 10Base-T Connector Pinout...23Ethernet AUI Connector Pinout (VS1000 Only)...
5List of TablesTable 1.Support Call Information...12Table 2.VS1000 Model and Serial Numbers...
6List of Tables
Product Overview 7IntroductionProduct OverviewThe Comtrol InterChangeVS 1000 is a rack-mountable or stackable “network appliance” that connects via Et
8 Installation OverviewIntroductionInstallation OverviewThe following outlines summarize the various VS1000/VS1100 installation scenarios. For more in
Installation Overview 9IntroductionAdding a VS1000 to an Existing InstallationA. Hardware Installation1. Install the VS1000.2. Install any associated
Commentaires sur ces manuels